Unlock A Gas Valve

Posted on February 7, 2012 by admin

Gas Valve
Gas Valve control the flow of natural gas that moves from a gas main line to a furnace. As of 2010, most new gas furnaces come equipped with natural gas valves. When a furnace is installed, the natural gas valve is calibrated so it properly senses the amount of gas, called gas pressure, that the natural gas lines are supplying it with.
1 Turn off the power supply to your gas tank. The gas tank must not be running while preparing to unlock the gas valve. If you do not turn off the gas tank, the pressure from the gas could damage the gas valve.
2 Determine the location of the gas valve. Some gas valves are located outside on or near your gas meters. Other gas valves are located right near the furnace in your basement or heating room.
3 Find which type of wrench will help unlock the gas valve Brass Bibcock. The two main wrenches most commonly used to lock or unlock a gas valve are adjustable or crescent wrenches. See which wrench fits over the gas valve.
4 Turn the gas valve in a counter-clockwise direction. A counter-clockwise direction should open or unlock the gas valve.
5 Perform any of the maintenance you wanted to do. Once you are finished, turn your gas valve in a clockwise direction until it is tight. Then, turn back the power supply of the gas tank.
The article comes from Brass Valves.

Posted in Gas Valve | Comments Off

Disassemble Gate Stop Valve

Posted on January 31, 2012 by admin

Brass Stop Valve
The Brass Gate Valve is ubiquitous. It has been used widely since its invention in the mid-1800s. Controlling the rate of steam was the main reason for its invention, for the valves of the 1800s were not strong enough to do what the industrialists needed. As time advanced, the gate valve was designed to handle gases other than steam. It can also be used for smaller capacities, such as hoses. Taking apart a gate valve may be necessary when it no longer functions as it should.
1 Locate and turn off the main water supply before disassembling the gate Stop Valve.
2 Take the screwdriver and remove the nut and the hand wheel from the top of the gate valve.
3 Unscrew the packing nut from the stem and remove the gland spring along with the packing gland from the top portion of the bonnet.
4 Remove all the nuts, lock washers and cap screws that are visible on the valve body and bonnet.
5 Take the bonnet, the gasket and the disc riser off of the stem. Unbolt the stem from the bonnet to complete the process.
The article comes from Brass Valves.

Posted in gate valve | Comments Off

The Way To Disassemble Brass Gate Valve

Posted on January 12, 2012 by admin

Brass Gate Valves With Solder Ends
The Brass Gate Valve is ubiquitous. It has been used widely since its invention in the mid-1800s. Controlling the rate of steam was the main reason for its invention, for the valves of the 1800s were not strong enough to do what the industrialists needed. As time advanced, the gate valve was designed to handle gases other than steam. It can also be used for smaller capacities, such as hoses. Taking apart a gate valve may be necessary when it no longer functions as it should.
1 Locate and turn off the main water supply before disassembling the gate Angle Valve.
2 Take the screwdriver and remove the nut and the hand wheel from the top of the gate valve.
3 Unscrew the packing nut from the stem and remove the gland spring along with the packing gland from the top portion of the bonnet.
4 Remove all the nuts, lock washers and cap screws that are visible on the valve body and bonnet.
5 Take the bonnet, the gasket and the disc riser off of the stem. Unbolt the stem from the bonnet to complete the process.
The article comes from Ball Valves.

Posted in ball valves, Brass Ball Valves | Comments Off

Discharge Mini Brass Ball Valves

Posted on January 4, 2012 by admin

Brass Mini Ball Valve
A Brass Ball Valves is (in simplest terms) a ball with a hole running through it. Turning the valve positions the hole to either block, partially block or complete the line of flow through the valve.
Advantages of ball valves include a good seal, or little to no leak-by when the valve is fully closed. A ball valve will turn regardless of the pressure on the supply side. If the hole through the valve is as large or larger than the supply pipe inner diameter, the ball valve will offer essentially no pressure drop or restriction when fully opened.
Ball valves are often used in high pressure liquid or gas lines, usually 6 inches or less in diameter, where a complete cut off is important.
Closing and Bleeding the Valve
1 Determine which section of the pipe you wish to close off from the rest of the system–upstream or downstream from the double block and bleed system.
2 Close the ball valve on the side of the block and bleed system that corresponds with the section of pipe you wish to isolate by turning the lever or wheel to the “off” position. Always close the valve slowly to prevent water hammering or pressure buildup in liquids.
3 Put on your safety goggles and gloves to protect yourself from high pressure or corrosive fluids inside the pipe. Place a bucket or container below the bleed Mini Ball Valve, in between the two ball valves in the block and bleed system, to catch the fluid as it is discharged from the valve.
4 Close the ball valve on the other side of the block and bleed system (the valve that corresponds to the section of pipe you wish to clear) by turning the wheel or level to the “off” position.
5 Slowly release the bleed valve, either by turning a release wheel or unscrewing a bolt in accordance with the manufacturer’s instructions. Be sure to discharge the valve slowly, as the contents may be under high pressure. Any fluid trapped in the middle portion of the block and bleed system will be discharged into the bucket or container you have prepared.
6 Close the bleed valve by turning the release wheel or replacing the screw or bolt. Slowly open the valve on the side of the block and bleed system that you wish to clear, refilling the bleed chamber with liquid. To completely clear the section of pipe, repeat the discharge process described in Steps 4 and 5 until the bleed valve releases no more fluid.
7 To resume normal function after the pipe has been cleared, slowly open the valves on both sides of the block and bleed system, one at a time. Make sure the bleed Brass Gate Valve is closed before opening the block valves.

Posted in ball valves | Comments Off

Unclog Kitchen Sink Drains

Posted on December 28, 2011 by admin

Kitchen Sink Drains
When you have a slow-running Kitchen Drain in your kitchen sink, it can be annoying to say the least. Over time, an accumulation of food particles and other debris can build up in your kitchen sink drain. This accumulation of debris can lead to a clog that can leave your kitchen drain running slow or not at all. Unclogging a drain doesn’t always require a plumber. Usually, removing a clog is a fairly easy fix that doesn’t take too much time.
1 Test the disposal first to determine if it’s the source of the clog. Turn on the switch; if you hear a humming, it’s probably clogged. Turn it off and unplug it. Insert an Allen wrench, often provided by the manufacturer for this very purpose, into the bottom hole on the disposal. Turn the blades until it breaks loose and turns freely. If the disposal makes no sound when you turn it on, the breaker may have tripped. Allow the disposal a few minutes to cool off and then press the reset button on the bottom before turning it back on.
2 Stuff a rag into the drain that is not clogged or seal it with the basket strainer if you have a double sink. Fill the clogged sink with about 3 to 4 inches of water. Center a plunger over the Sink Drain. Push the plunger up and down to dislodge the clog.
3 Place a bucket underneath the drain under the sink to catch water. Unscrew the sink trap. Hand loosen it or use a pipe wrench.
4 Unscrew the horizontal trap arm with the wrench and remove.
5 Push a cable auger, also called a snake, through the stub-out. When you feel resistance, pull back about 18 inches of cable and tighten the screw. Turn the handle clockwise and push on the auger. Pull back another 18 inches of cable. Keep repeating by pushing it in, turning the handle and pushing forward until the clog breaks loose.
6 Remove the cable from the stub-out when the clog is cleared. Replace the trap arm and trap.
7 Run the hot water to test if the sink is draining. Flush the drain with hot water until it does drain. Center the plunger over the drain again and plunge it to loosen any leftover bits of clog.
8 Pour about 1/2 cup of white vinegar and a 1/2 cup of baking soda into the drain to clean and freshen it. Let it sit for a few minutes and then run warm water through the drain to flush it.
The article comes from Brass Valves.

Posted in Sink Drains | Comments Off

Brass Check Valve Advantages

Posted on December 20, 2011 by admin

Brass Check Valve
A Brass Check Valve is a device that is installed in the pipes connected to a water heater to prevent the backflow of water. When the water flows forward toward the check valve, the valve opens to allow the water to flow through. When the flow of water stops, the check valve closes so that the water cannot reverse direction and flow back the way it came.Brass Angle Valve
Advantages of Check Valves
Check valves are important in a water heater because they prevent flooding or overflowing. They also stop the water from constantly flowing backwards, even when the heater is off. This prevents eroding of the pipes and saves power.
Check valves are useful in several different types of devices. They stop flooding in water-related devices, such as sump pumps and water heaters. They also protect equipment that can be harmed by the reverse flow of material, such as control valves, strainers, and flow meters. In addition, check valves can stop material from constantly flowing backwards when a device is off, which can save power and protect the parts of the device.
The article comes from Brass Valves.

Posted in check valve | Comments Off

Gate Valve VS. Angle Valve

Posted on December 11, 2011 by admin

Brass Gate Valves
Gate Valve are primarily designed to start or stop flow, and when a straight-line flow of fluid and minimum flow restriction are needed. In service, these valves generally are either fully open or fully closed.
The disk of a gate valve is completely removed when the valve is fully open; the disk is fully drawn up into the valve bonnet. This leaves an opening for flow through the valve at the same inside diameter as the pipesystem in which the valve is installed.
A gate valve can be used for a wide range of liquids and provides a tight seal when closed.
Advantages of using gate valves:
Good shutoff features
Gate Valves are bidirectional and therefore they can be used in two directions
Pressure loss through the valve is minimal
An Angle Valve is a flow control device that utilizes a piston seated within a metal casing in order to control the flow of fluid or gas through a system. The valve gets its name from the fact that the piston in the system is set at an angle inside the casing in order to provide maximum flow throughout the system. The casing in an angle valve is most typically made from metal or plastic. While any handle can be used, an angle valve usually has a circular handle in order to facilitate the screw mechanism that raises and lowers the valve. Angle valves come in a variety of sizes suited for most applications.
Advantages of using Angle Valve:
? transfer from the inside and outside the outlet.
? is too much water pressure can be adjusted in the triangle above the valve, turn down a little,
? is the role of the switch, if the faucet leaks and other phenomena occur, turn off the valve may be the triangle, not the total valve off at home.
? is nice, so the general home decoration are essential plumbing parts, so when fitting new home will be referred to the designers.
The article comes from Brass Valves.Kingsir valve, manufacture of brass ball valves, angle valves, check valves, stop valves, gas valves, gate valves and bibcocks.

Posted in angle valve, gate valve | Comments Off

Industrial Ball Valve – An Essential Component

Posted on December 8, 2011 by admin

Industrial valves are factors from the machinery which could be utilized to look after the flow of liquids, solids or gases through them. there are numerous several commercial valves which could be produced preserving several needs of several sorts of commercial machinery. Most standard amid them are ball valves. Other several sorts of valves consist of Gate valves, butterfly valves and planet valves. Ball valves are relatively broadly utilized in almost all sorts of commercial needs and residential plumbing related needs. Ball valves are totally nothing but balls positioned near to the inside of pipes that look after the flow mechanism from the machinery. There are lots of sorts of ball valves around although in the marketplace centered near to the pace requirements, temperatures requirements, as well as the stress needs of marketplace machinery. several sorts of ball valves are stainless metal ball valves, significant stress ball valves, brass ball valves, threaded valves, and so on.

When the fluid passes through the ball valves, the way in which the fluid flows may be controlled with the character from the ball valve used. The ball valves have spherical discs within that regulate the flow of something that passes through it. centered near to the mode of operation the fact that ball valve utilizes to look after the flow, it may be classified into several other several categories. complete port, two-way, three-way, four-way, multi-port, decreased port, and V-port are several of them.

Ball valves have flow resistances based on the sort from the port that is used. Also, they are uncomplicated to run which enables it to regulate the flow in split of the second. They have manually operated handles that may be turned on or away to turn on or shut decrease the fluid flow through the pipelines. Ball valves are very much durable thinking about the fact that operation is relatively uncomplicated as well as the flow regulation mechanism does not take concerning the ball to complement on and tear easily. It may be practically utilized to look after the flow of any type of fluid as well as safe particles. The passage way features a surface area that does not restrict the flow, as well as the mechanism controls the stress and pace from the flow.

Ball valves may be also classified depending upon the quantity of pieces the fact that whole product contains. individual product body, three product whole body valves, split body, and welded are probably the most standard sorts used. Most ball valves do not phone for lubricators to run which enables it to last critically extended for very much much more than twenty years. buying the ball valves away from your proper vendor is relatively needed to create specific the fact that valves are up to the needs in quality. Nowadays, exceptional commercial valves may be ordered on the net to help save the time and vitality needed to locate a excellent vendor and make the purchase.

Posted in ball valves, Brass Ball Valves | Tagged , , | Comments Off

Install And Fitting A Kitchen Mixer Tap

Posted on November 21, 2011 by admin

Sink Mixer, sink taps, Kitchen Sink Mixer 1 Clean the counter and the hole into which the faucet will connect to the counter by scraping it with a putty knife or brushing it with a wire brush. 2 Apply plumbers putty to the underside of the Sink Mixer decorative plate, which is known as a escutcheon. Slide the assembly of the tap through the hole in the counter and press the escutcheon to the counter over the decorative hole. Wait for the putty to dry before continuing. 3 Place the locking nuts and washers onto the valves beneath the mixer following the manufacturer’s directions. Directions will vary among faucet makers. 4 Slip an adapter onto the end of each valve. 5 Slip a supply nut onto the hot or cold water supply pipes. Slip the end of the hot or cold water supply pipes into the adapter located at the end of the hot and cold water valves on the faucet assembly. Tighten the supply nut onto the adapter to hold the connection in place. 6 Turn on the water supply by turning on the knob to the primary water supply valve. Check your sink for leaks and tighten all nuts at the point where the leaks occur until the leaking stops. The copper pipes we have initially caused a problem due to their position and proximity to the nut fixing that was holding the original tap in place. we must commend the plumber that originally put this in place. It took a lot of energy to loosen it sufficiently for me to undo with my fingers. The key tool used to do this was a 10mm spanner, this could only be done once the pipes had been cut as discussed previously with the proximity to the piping. we used a standard pipe cutter to slice through the copper piping tightening the grip gently after each turn to avoid denting the pipe. Once both of these task had been completed the Sink Mixer lifted away from the basin without any trouble, giving the basin a quick wipe to remove any lime scale build up or dirt that had accumulated, we was ready to fit my new tap. On the end of the copper piping we pushed down the 15mm end of the reducing valves making sure they stayed in place by pulling on them slightly making sure they didn’t move up and down when doing so, we then fitted the new pipes to the bottom of the new tap and placed gently on the basin with the pipe work protruding through the hole in the basin making them parallel with the existing pipe work and my reducing valves. Marking the position to cut on the new pipes we removed it from its position and cut the pipes accordingly and reattached them. Once trimmed we attached the ribbed steel rod to the base of the unit and put the tap in place on the basin. simply pushing the new pipe work into the 10mm end of the quick plumb fittings the Sink Mixer was connected and sealed. Finally we screwed the nut up the steel rod tightening up to the washer with my fingers, we then tightened further with a 10mm spanner until the pull out spray kitchen sink mixer was firmly held in place. This is the most important part of the entire job. turning the water back on! If you hear a pop and a his it means the quick plumb fitting is not pushed onto the pipes enough to form a full seal, If this happens (which it did) turn the water off go back to the fitting and apply pressure (down on the new pipe work and up on the old pipe work) and one of them will pop into place, you can then turn the water back on.

Posted in taps | Comments Off

How to find a Brass Gate Valve supplier on the internet?

Posted on September 27, 2011 by admin

Some people would like to find suppliers from the internet. Because the internet contact such as email and msn (the most common IM tool in business) is no cost and fast.

Here I give you an idea a very common way to search sellers on the internet.

For example: you are looking for a Brass Gate Valve and Brass Check Valve

The most common search engine: www.google.com www.yahoo.com www.msn.com

Maybe you consider that go to the search engine and type “Brass Gate Valve”,how ever you would to easy to get the suppliers, you would always find some Brass Gate Valve online shop.They only sell to the personal.

So please try Brass Gate Valve manufacturer or Brass Gate Valve wholesale, because the suppliers of Brass Gate Valve named themself as a manufacturer or wholesalers.

Now try again,you will more easily to find the suppliers now.

Posted in Brass Valves, check valve, gate valve | Tagged , | Comments Off